Beckhoff’s EP9224 smart power box offers internal current and voltage measurement in addition to the ability to connect four EtherCAT Box power supply branches. The values are available to the controller via EtherCAT and support the preventive maintenance of machines and plants as well as error diagnostics, especially in conjunction with the data-logging function.
The power consumption for the control and peripheral voltage is monitored, limited and if necessary also switched off in each 24 V supply branch of the smart power box. The input voltage and current as well as all output currents can be transferred by EtherCAT to the controller as process data and evaluated. In case of an error a continuous data log can be retrieved, allowing the cause of the error to be identified more easily. This information is recorded every 1, 10, 25, 100 or 1000 ms as required.
The current and voltage measurement plus the data logging provide a deep insight into the machine and considerably simplify and accelerate service. In this way the monitoring of the momentary current values minimises the response times to any errors. As a form of Condition Monitoring, this transparency in the system and thus the early identification of deviating machine states also supplies the ideal basis for preventive maintenance.
Higher total current simplifies system wiring
EtherCAT Box modules with IP67 protection typically use M8 plug connectors for the supply of power, but these are only suitable for a maximum current of 4 A. Therefore, it may no longer be possible to simply loop the supply through where modules have a large number of outputs.
The EP9224 smart power box offers the ideal solution for this. Equipped with 22 mm plug connectors, it allows a total current of 16 A for each control and peripheral voltage with cable cross-sections of 1,5 and 2,5 mm. Even considerably higher starting currents are briefly permissible at the outputs, so that the trouble-free start-up of the connected devices is guaranteed. This gives rise to significantly simpler and cheaper plant wiring compared to the otherwise necessary additional terminal boxes with fuses.
All eyes on the modern DCS platform Schneider Electric South Africa
PLCs, DCSs & Controllers
Modernised DCS platforms are no longer confined to hardware-dependent architectures. These systems have evolved to combine the strengths of both PLCs and DCS while adding capabilities that make them more open, resilient and collaborative.
Read more...Automation solution for waste management at incineration facility
PLCs, DCSs & Controllers
Valmet is to deliver an automation system to Seongnam City’s incineration facility currently under construction in South Korea. By leveraging intelligent automation, the plant will optimise energy production, minimise emissions and deliver efficient, consistent performance throughout its entire lifecycle.
Read more...Valmet’s supplies DCS to Europe’s largest electric boiler plant Valmet South Africa
PLCs, DCSs & Controllers
Valmet will supply an automation system to Helen’s Hanasaari electric boiler plant and a thermal accumulator being built in Helsinki, Finland. Once completed, it will be Europe’s largest electric boiler plant.
Read more...Technology blueprint paves way for e-methanol fuel expansion Schneider Electric South Africa
PLCs, DCSs & Controllers
Schneider Electric has delivered the technology stack behind European Energy’s Kassø Power-to-Xfacility, the world’s first commercially viable e-methanol plant.
Read more...PC-based control in the plastics industry Beckhoff Automation
Fieldbus & Industrial Networking
Nissei Plastic, an injection moulding machine manufacturer based in Japan is implementing a worldwide tend towards open automation systems from experienced specialists using PC and EtherCAT-based control technology from Beckhoff.
Read more...PC-based control for flat wire motors for electric vehicles Beckhoff Automation
Editor's Choice Motion Control & Drives
Special machine manufacturer, ruhlamat Huarui Automation Technologies has unveiled the second generation of its mass production line for flexible stators with bar winding (pins). This enables an extremely short production cycle and line changeover times, supported by PC- and EtherCAT-based control technology from Beckhoff.
Read more...PC-based control for flat wire motors for electric vehicles Beckhoff Automation
Fieldbus & Industrial Networking
Special machine manufacturer, ruhlamat Huarui Automation Technologies unveiled the second generation of its mass production line for flexible stators with bar winding. This enables extremely short production cycle and line changeover times, supported by PC- and EtherCAT-based control technology from Beckhoff.
Read more...New energy-efficient evaporation line for dissolving pulp production Valmet South Africa
PLCs, DCSs & Controllers
Valmet will deliver a new evaporation line to Altri Biotek mill in Portugal. This delivery is part of Altri’s €75 million project to convert the Biotek mill to produce dissolving pulp for the textile industry.
Read more...Hans Beckhoff receives German Mechanical Engineering Award Beckhoff Automation
News
Hans Beckhoff has received the 2025 German Mechanical Engineering Award. This prestigious award honours entrepreneurs who have set standards in machine and system engineering, driven innovation, and taken on social responsibility.
While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.
printer friendly version