Crusher gap measurement

February 2021 Maintenance, Test & Measurement, Calibration

Developed by Mintap, based in Perth, Western Australia, the Closed Side Setting (CSS) measurement device – the C-Gap – is now available through South African-based Control Systems Rustenburg. C-Gap offers accuracy, safety and reliability to the quarrying and mining industries for the measurement of the CSS in gyratory, jaw and cone crushers.

The C-Gap works by placing selected high-density rubber hollow bulbs into the crusher mantle. When the bulb is squeezed between the fixed and moving plates, the air pressure in the hose increases, then, by correlating the air pressure through manual calibration, the CSS is measured between 7 mm and 220 mm with an accuracy of 1 mm.

The process of measuring the CSS on all four sides of a cone crusher takes less than five minutes and requires only one operator. Jaw and gyratory crushers are about the same.

The C-Gap effectively replaces current methods of CSS measurement, namely the use of lead weights, steel drums, aluminium or clay balls, or manual measurement. Because the procedure is so quick and easy, the CSS can be measured every shift on all crushers, ensuring consistent crusher operation by achieving targeted set points across all crews.

Maintaining the CSS

To date, there has not been a quick, accurate and safe way to measure the CSS in larger primary crushers; the CSS on these crushers is usually measured during shutdowns only, meaning it runs unchecked for potentially weeks at a time. This results in reduced crusher performance, placing increased emphasis on downstream circuits.

By measuring every shift, the CSS can be maintained and mantle wear can be documented, assisting with service planning. Operators on sites using the C-Gap commended its safety advantage over the lead weights. Through site comparative trials they noted the C-Gap had an improved accuracy over the use of traditional means. Cost-benefit analyses of sites that currently use lead weights have shown a payback within six months of purchase, when one considers the cost and safe disposal of these. Sites that do not use lead weights enjoy the improved accuracy of the C-Gap.

Further reading:

Rethinking corrosion protection in process plants
Omniflex Remote Monitoring Specialists Maintenance, Test & Measurement, Calibration
Remote monitoring is changing how cathodic and anodic protection systems are managed in process plants, giving operators continuous visibility of corrosion protection performance and enabling more proactive maintenance decisions.

Read more...

---

Installation safety tester
Vepac Electronics Maintenance, Test & Measurement, Calibration
A combination measuring device for testing electrical installations, offering safety tests including RCD, voltage, loop, low-resistance, earth resistance and insulation checks via a 3,5-inch TFT colour display.

Read more...

---

Bringing predictive maintenance to the next level in the pulp and paper industry
Maintenance, Test & Measurement, Calibration
ennomotive has launched an international competition seeking innovative predictive maintenance solutions for conveyor belt systems, addressing a real operational challenge faced by pulp and paper company CMPC.

Read more...

---

Vibration sensor with CANopen interface for mobile machines
ifm - South Africa Maintenance, Test & Measurement, Calibration
ifm’s 3-axis VMB301 condition monitoring sensor integrates into the vehicle network via CANopen, delivering real-time bearing, vibration and temperature data to help mobile machines avoid costly damage and downtime.

Read more...

---

Linear regulated 2-channel laboratory power supply
Vepac Electronics Maintenance, Test & Measurement, Calibration
Vepac Electronics offers a dual-channel laboratory power supply built for safe, precise testing in laboratories and workshops.

Read more...

---

When oil gets old
Wearcheck Maintenance, Test & Measurement, Calibration
WearCheck explains how oxidation breaks down lubricating oils over time, and how routine oil analysis can catch the warning signs before equipment failure.

Read more...

---

SEW-EURODRIVE brings intelligent energy optimisation to Electra Mining
SEW-EURODRIVE Maintenance, Test & Measurement, Calibration
At Electra Mining Africa 2026, SEW-EURODRIVE will showcase its DriveRadar IoT platform for predictive maintenance and real-time energy optimisation, alongside plant energy surveys and an 1850 kW medium voltage motor display.

Read more...

---

Thermal imaging camera with high thermal resolution
Vepac Electronics Temperature Measurement Maintenance, Test & Measurement, Calibration
Vepac Electronics introduces a compact thermal imaging camera that helps technicians spot temperature problems before they become costly failures.

Read more...

---

What your lubricant really costs
Maintenance, Test & Measurement, Calibration
The purchase price of an industrial lubricant is only a fraction of what lubrication truly costs a business. Lubrication Engineers South Africa explains how shifting from unit price to total cost of ownership changes the equation significantly.

Read more...

---

Rethinking corrosion protection in process plants
Omniflex Remote Monitoring Specialists Maintenance, Test & Measurement, Calibration
Omniflex explains how integrating remote monitoring and cloud-based platforms into cathodic and anodic protection systems is helping process plant operators stay ahead of corrosion and make smarter maintenance decisions.

Read more...

---