The dV-2 PS is a sophisticated digital pressure gauge with two independent pressure switch outputs. The gauge employs Keller's proven microprocessor technology to produce highly accurate results. All readings are linearised and temperature corrected, to give an accuracy of 0,2% FS.
There are two independent switches for high and low control functions. These are solid state and therefore not subject to wear. The switch points are programmed directly from the two front panel buttons and a menu system. Alternatively, the dV-2 PS can be connected via the RS485 link to a laptop or PC, and configured using Keller's 'Pressure Switch Console' software. User defined configurations can be stored on the computer for future reference. Pressure sequences can also be monitored and recorded on the PC for application diagnostic purposes using Keller's Read30 software.
Two independent floating switches are available; neither is subject to wear and they can be operated individually as make or break contacts. The switch can provide a window function or be utilised as a hysteresis switch. These switching functions enable the dV-2 PS to carry out control tasks. Respective switch output status is displayed on an LED located on the front.
The dV-2 PS has the following functions:
* High/low - maximum and minimum values are indicated via the select button.
* Reset - allows the maximum and minimum value to be reset at the actual pressure value.
* Zero - sets the zero to any value as a new zero reference. Barometric pressure variations can thus be compensated. The factory setting of the zero for the ranges ≤31 bar is at 0 bar absolute. For sealed gauge pressure measurements, activate 'ZERO SET' at ambient pressure. Instruments with ranges >31 bar are calibrated in a sealed gauge mode with ambient pressure as a zero reference.
* Switch - configuration of the switch outputs. Switch points, switch window, switch hysteresis, open and close.
* Units - pressure can be displayed in bar, MPa or PSI.
Randburg-based Instrotech is the exclusive distributor for Keller products which are Swiss manufactured.
For more information contact Andrew Huart, Instrotech, +27 (0) 11 462 1920, [email protected]
Groundwater level measurement using LoRa module Instrotech
Level Measurement & Control
Monitoring groundwater levels across large industrial sites is critical. Salzgitter Digital Solution was tasked with developing a fully automated and digital monitoring system using Long Range Wide Area Network technology.
Read more...Infrared solutions for glass manufacturing challenges Instrotech
Temperature Measurement
In the glass industry, infrared temperature monitoring is crucial for maintaining product quality and process efficiency. Instrotech has infrared sensors and cameras which provide non-contact temperature measurements, making them ideal for these high-temperature environments.
Read more...Embracing digital precision in instrument manufacturing SA Gauge
Pressure Measurement & Control
In modern instrumentation manufacturing, precision is no longer limited to measurement alone. One area undergoing notable change is the printing of instrument plates and branded components.
Read more...Senix sensors provide flood warnings Instrotech
Flow Measurement & Control
To create the world’s most sophisticated flood monitoring and forecasting system, the US State of Iowa’s Flood Centre (IFC) uses more than 200 Senix ToughSonic 30 and ToughSonic 50 ultrasonic sensors to measure water levels in streams across the state.
Read more...Sensors measure palm oil tank level Instrotech
Level Measurement & Control
The Senix ToughSonic 30 accurately measures and monitors the level of palm oil in large tanks approximately nine metres in height.
Read more...Water under pressure VEGA Controls SA
Pressure Measurement & Control
The need for real-time monitoring and precise control over water distribution has never been more critical. VEGA’s range of pressure sensors and level instruments plays an important role in ensuring that water systems operate efficiently.
Read more...Paper might carry the message, but pressure carries the process VEGA Controls SA
Pressure Measurement & Control
VEGABAR pressure transmitters are designed to address the unique challenges faced by the pulp and paper industry. Built for durability and precision, they ensure reliable pressure monitoring in aggressive environments.
Read more...Capsules, steam and cream VEGA Controls SA
Pressure Measurement & Control
African cosmetic brands are increasingly outsourcing production to specialised contract manufacturers who use automation and high-precision tools to ensure quality and adapt quickly to regulatory changes. VEGA’s suite of level and pressure measurement solutions offers a robust foundation for profitability and quality assurance.
Read more...Differential pressure measurement made simple VEGA Controls SA
Pressure Measurement & Control
The VEGADIF 85 serves as an exemplary model of a differential pressure sensor. It combines universal applicability with high operational dependability and integrated overload protection, ensuring consistent performance even in the harshest conditions.
While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.
printer friendly version