Maintenance, Test & Measurement, Calibration


Pressure and vacuum calibration laboratory

April 2003 Maintenance, Test & Measurement, Calibration Perimeter Security, Alarms & Intruder Detection

Rhomberg has a laboratory accredited by the South African National Accreditation System (SANAS) for pressure and vacuum. The laboratory complies with the requirements of ISO 17025 whereby all calibrations performed are traceable to national and international standards.

Due to the implementation of quality systems installed by the industry, having to comply with ISO 9000 requirements it is a requirement provide traceable calibrations. With this in mind Rhomberg now offers a calibration and repair service with facilities to provide a quick turnaround time of 1-2 days upon receipt of the instruments at the same time upholding a high standard of workmanship.

As one of the largest manufacturers in Africa, the repair and calibration service complements the marketing of new and replacement gauges and instrumentation. In addition an on-site service is offered to the industry where speedy turnaround time is imperative.

The calibration facility encompasses but is not limited to the following:

* Test gauges to an accuracy of 0,10% full scale.

* Pressures ranging from 1250 Pa to 1200 MPa.

* Up to 330 MPa for standard calibration.

* Best measurement capabilities of 0,05%.

* On site calibration up to 60 MPa.

* Oil free calibrations where required.

* Service excellence.

* Temperature calibration from -20°C.

For more information contact Paul Tredoux, Rhomberg, 021 552 4930, pault@rhomberg.co.za, www.rhomberg.co.za





Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

Gas instrument maintenance made easy
September 2021, Comtest , Maintenance, Test & Measurement, Calibration
Comtest is offering iNet Exchange that allows customers to say goodbye to gas instrument maintenance and say hello to an always-ready instrument fleet.

Read more...
Compressed air purity analyser
September 2021, Artic Driers International , Maintenance, Test & Measurement, Calibration
These SUTO-iTEC units ensure that c/air systems comply with the relevant ISO 8573 air standard.

Read more...
Remote monitoring for CP systems
August 2021, Omniflex Remote Monitoring Specialists , Maintenance, Test & Measurement, Calibration
PowerView iREF8 allows businesses to add remote monitoring to existing cathodic protection (CP) systems.

Read more...
Online monitoring of haul trucks
August 2021, SKF South Africa , Maintenance, Test & Measurement, Calibration
IMx-16 Multilog online monitoring systems on two mobile mining haul trucks at a leading copper mine in Zambia predict critical component failures and allow for planned predictive maintenance procedures to be carried out.

Read more...
Monitoring oil and gas pipelines
August 2021, RJ Connect , Maintenance, Test & Measurement, Calibration
Moxa’s MDS-G4020 series offers a modular platform that can be fitted with fibre interfaces to connect pipeline subsystems to a control centre over long distances.

Read more...
Non-contact meter for voltage measurements
August 2021, Comtest , Maintenance, Test & Measurement, Calibration
The new Fluke 377 FC and 378 FC Non-Contact Voltage True-RMS AC/DC Clamp Meters can measure voltage and current simultaneously without touching a live wire.

Read more...
Optimum efficiency at healthcare facilities
Technews Industry Guide: Sustainable Manufacturing 2021, Comtest , Maintenance, Test & Measurement, Calibration
Comtest solutions to help surpass safety standards with optimum efficiency.

Read more...
Remove water from factory air
Technews Industry Guide: Sustainable Manufacturing 2021, SMC Corporation South Africa , Maintenance, Test & Measurement, Calibration
A leading cause of costly downtime and emergency maintenance is water vapour and the resulting condensed water that is trapped in factory compressed air.

Read more...
Mitigating manufacturing downtime with smart services
Technews Industry Guide: Sustainable Manufacturing 2021, Schneider Electric South Africa , Maintenance, Test & Measurement, Calibration
The reliability of equipment forms a fundamental part of business sustainability, particularly when it comes to production continuity and downtime avoidance.

Read more...
How to avoid false alarms with PIDS
Residential Security Handbook 2021: Secure Living , Residential Estate (Industry), Perimeter Security, Alarms & Intruder Detection, Products
If you have installed a perimeter intrusion detection system around your property, you have taken the first step in protecting your most valuable asset, says Tiaan Janse van Rensburg.

Read more...