Pressure Measurement & Control


Protecting pressure gauges and transmitters against water hammer

April 2015 Pressure Measurement & Control

Water hammer is a high pressure surge or wave created by the kinetic energy of moving fluid when it is rapidly forced to stop or change direction, altering the liquid’s velocity. Rapid stopping or starting or changing of direction of an incompressible fluid like water or oil in a system is caused by a variety of valves or pumps.

Myth: A pressure spike cannot exceed the normal pressure in the system.

Fact: Pressure spikes can reach up to eight times the system pressure.

Gauge before water hammer.
Gauge before water hammer.

Even though pressure spikes may only last milliseconds, the potential damage is lasting. One of the main concerns of hydraulic and other system designers is how to eliminate or minimise water hammer. Methods and formulas for calculating water hammer pressures are freely available online.

Pressure gauges and transmitters fitted to measure normal line pressure at the receiving end of these ‘pressure spikes’ are often irreparably damaged if not suitably protected.

Why does water hammer affect pressure gauges and transmitters?

Overpressured gauge  – result of water hammer.
Overpressured gauge – result of water hammer.

Pressure gauges and transmitters are designed to measure pressures up to the full scale value of the instrument. For short periods, these instruments may accept an overpressure of a percentage of the rated full scale pressure, without permanent damage.

The measuring sensor of pressure gauges (bourdon tube), and transmitters (diaphragm), are normally manufactured from a flexible elastomeric type material to ensure accuracy and repeatability.

Good quality pressure gauge bourdon tubes are designed, manufactured and tested to withstand (for short periods) up to 1,3 times the rated pressure in the case of normal pressure gauges (up to 5 times more in the case of some diaphragm operated pressure gauges that do not use bourdon tubes, but with a limited range of max 2500 kPa) without permanent damage to the instrument. Most pressure transmitters can, for short periods, withstand 1,5 to 2 times the rated full scale value without permanent damage. Pressure spikes exceeding these limits can cause the elastomeric sensors to deform permanently, rendering them unable to return to zero. Accuracy and repeatability may be affected and in extreme cases, rupturing of the sensor may occur.

Gauges are sometimes returned to the manufacturer for investigation, completely over-pressured and often with a ruptured bourdon tube. Once informed of the gauge’s condition, we often hear, “But how can it be possible? It is a 1000 kPa gauge and the pump can generate a maximum of 600 kPa.” Water hammer is the most likely cause of damage in such a scenario.

Protecting pressure gauges and transmitters against water hammer

The progression of the water hammer shockwave needs to be detained and slowed before reaching the instrument sensor. SA Gauge manufactures several such devices in order to achieve this. The most common and economical, is a simple threaded snubbing screw that screws into the process connection of the gauge, restricting the pressure port to minimise flow into the gauge. In severe cases, a length of small bore capillary tube is attached to the snubber to increase the effectiveness. Other devices like external adjustable flow restrictors, piston type snubbers and needle valves are also available to choke the offending pressure surge to an acceptable level.

It is important to note that these devices will not protect the instruments against sustained overpressure, which will still damage the instruments. An overpressure protector will be required in these cases.

For more information contact Chris du Plessis, SA Gauge, +27 (0)31 579 2216, chris@sagauge.com, www.sagauge.com



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

Highest energy efficiency reduces operating costs
November 2020, WIKA Instruments , Pressure Measurement & Control
Pressure loss is synonymous with higher energy costs that must be spent for normal operation.

Read more...
Top-quality drinking water through ozone treatment
January 2021, VEGA Controls SA , Pressure Measurement & Control
Vega’s pressure transducers make an important contribution to the continuous processing of top-quality drinking water.

Read more...
Robust needle valve for high-pressure applications
January 2021, WIKA Instruments , Pressure Measurement & Control
WIKA has supplemented its portfolio of shut-off valves with the model HPNV high-pressure needle valve.

Read more...
Ceramic and metallic measuring cells optimise additive production at BASF
September 2020, VEGA Controls SA , Pressure Measurement & Control
The combination of a ceramic Certec and a metallic Metec measuring cell proved to be the perfect combination from VEGA.

Read more...
Combination of digital pressure gauge and smartphone via Bluetooth
August 2020, WIKA Instruments , Pressure Measurement & Control
For optimal process efficiency in pharmaceutical applications, solutions featuring wireless communication are becoming first choice, especially in mobile applications.

Read more...
Thermometer guns on coronavirus front lines: accurate or not?
July 2020, SA Gauge , News
If you have not already had your temperature taken before entering a public building, there is a good chance you soon will. It has become an iconic image of the coronavirus outbreak worldwide: a masked ...

Read more...
Upgrade for PSM-700 pressure switch
May 2020, WIKA Instruments , Pressure Measurement & Control
WIKA’s PSM-700 pressure switch with large adjustable switch differential is now able to withstand higher process temperatures. Previously, the process media was limited to a temperature range of -30...

Read more...
Hygienic food production
June 2020, VEGA Controls SA , Pressure Measurement & Control
Food production is a matter of trust, and hygiene is the number one priority in the manufacturing process. Success is determined by both the reliability and the efficiency that make flawless production ...

Read more...
Upgrade for PSM-700 pressure switch
June 2020, WIKA Instruments , Pressure Measurement & Control
WIKA’s PSM-700 pressure switch with large adjustable switch differential is now able to withstand higher process temperatures. Previously, the process media was limited to a temperature range of -30ºC ...

Read more...
Vega’s solutions for pharmaceutical applications
May 2020, VEGA Controls SA , Pressure Measurement & Control
The special challenges faced by the pharmaceutical industry result from the wide diversity of its processes. Success depends on the consistency and continuity of the production processes, whether it be ...

Read more...