Pressure Measurement & Control


Why does water hammer affect pressure gauges and transmitters?

October 2019 Pressure Measurement & Control

Water hammer is a high pressure surge or wave created by the kinetic energy of moving fluid when it is rapidly forced to stop or change direction, altering the liquid’s velocity. Rapid stopping or starting or changing of direction of an incompressible fluid like water or oil in a system is caused by a variety of valves or pumps.

Myth: A pressure spike cannot exceed the normal pressure in the system.

Fact: Pressure spikes can reach up to eight times the system pressure.

Even though pressure spikes may only last milliseconds, the potential damage is lasting. One of the main concerns of hydraulic and other system designers is how to eliminate or minimise water hammer. Methods and formulas for calculating water hammer pressures are freely available online.

Pressure gauges and transmitters fitted to measure normal line pressure at the receiving end of these ‘pressure spikes’ are often irreparably damaged if not suitably protected.

Why does water hammer affect pressure gauges and transmitters?


Gauge before water hammer.

Pressure gauges and transmitters are designed to measure pressures up to the full scale value of the instrument. For short periods, these instruments may accept an overpressure of a percentage of the rated full scale pressure, without permanent damage.

The measuring sensor of pressure gauges (bourdon tube), and transmitters (diaphragm), are normally manufactured from a flexible elastomeric type material to ensure accuracy and repeatability.

Good quality pressure gauge bourdon tubes are designed, manufactured and tested to withstand (for short periods) up to 1,3 times the rated pressure in the case of normal pressure gauges (up to 5 times more in the case of some diaphragm operated pressure gauges that do not use bourdon tubes, but with a limited range of max 2500 kPa) without permanent damage to the instrument. Most pressure transmitters can, for short periods, withstand 1,5 to 2 times the rated full scale value without permanent damage. Pressure spikes exceeding these limits can cause the elastomeric sensors to deform permanently, rendering them unable to return to zero. Accuracy and repeatability may be affected and in extreme cases, rupturing of the sensor may occur.


Overpressured gauge - result of water hammer.

Gauges are sometimes returned to the manufacturer for investigation, completely over-pressured and often with a ruptured bourdon tube. Once informed of the gauge’s condition, we often hear, “But how can it be possible? It is a 1000 kPa gauge and the pump can generate a maximum of 600 kPa.” Water hammer is the most likely cause of damage in such a scenario.

Protecting pressure gauges and transmitters against water hammer

The progression of the water hammer shockwave needs to be detained and slowed before reaching the instrument sensor. SA Gauge manufactures several such devices in order to achieve this. The most common and economical, is a simple threaded snubbing screw that screws into the process connection of the gauge, restricting the pressure port to minimise flow into the gauge. In severe cases, a length of small bore capillary tube is attached to the snubber to increase the effectiveness. Other devices like external adjustable flow restrictors, piston type snubbers and needle valves are also available to choke the offending pressure surge to an acceptable level.

It is important to note that these devices will not protect the instruments against sustained overpressure, which will still damage the instruments. An overpressure protector will be required in these cases.

For more information contact Chris du Plessis, SA Gauge, +27 31 579 2216, chris@sagauge.com, www.sagauge.com


Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

Tough OEM pressure switch from WIKA
October 2019, WIKA Instruments , Pressure Measurement & Control
The PSD-4-ECO pressure switch from WIKA is designed for harsh ambient conditions, and is optimised for OEM integration. With a diameter of 29 mm, the model is very slim and through the arrangement of ...

Read more...
Hygienic pressure transmitter
September 2019, ASSTech Process Electronics + Instrumentation , Pressure Measurement & Control
The pressure transmitter Jumo Taros S46 H – available locally from ASSTech – is designed according to the hygienic requirements for precision measurement and longevity. The high-level protection type ...

Read more...
Electronic pressure gauges for Ex areas
September 2019, Instrotech , Pressure Measurement & Control
Instrotech now offers Keller’s range of intrinsically safe electronic pressure gauges for use in areas subject to gas explosion risks. The type approvals are compliant with the ATEX Explosion Protection ...

Read more...
PS17 differential pressure ­transmitter
August 2019, Vepac Electronics , Pressure Measurement & Control
Differential pressure transmitters are used for regulating HVAC systems and for monitoring filters. The devices can also monitor under and overpressures in cleanrooms or mini-environments. halstrup-walcher, ...

Read more...
The dream team for heat and condensate
August 2019, VEGA Controls SA , Pressure Measurement & Control
An innovative duo of ceramic and metallic measuring cells from VEGA optimises pressure measurement in a distillation process at BASF.

Read more...
Pressure sensors for Industry 4.0
Technews Industry Guide: Industrial Internet of Things & Industry 4.0, Turck Banner , Pressure Measurement & Control
Turck’s new pressure sensors of the PS+ series offer complete access to sensor parameters via IO-Link.

Read more...
New monoflange design prevents fugitive emissions
July 2019, WIKA Instruments , Pressure Measurement & Control
The new WIKA model IVM monoflange for connecting pressure measuring instruments to the process is particularly suitable for applications involving critical liquids, gases and vapours. Special seals also ...

Read more...
Pressure transmitters for mobile equipment
June 2019, Turck Banner , Pressure Measurement & Control
In order to provide solutions for use in mobile equipment, Turck has expanded its portfolio of pressure sensors with the introduction of the PT1100/2100 transmitters. This includes mining, forestry, agricultural ...

Read more...
Understanding accuracy specifications
May 2019, I-PAS (Industrial Process Automation Solutions) , Pressure Measurement & Control
Pressure measurement device accuracies are commonly specified as percentage of full scale, or percentage of reading, and the difference is significant. If an accuracy statement simply names a percentage ...

Read more...
Miniature IR thermometer for plastic film
May 2019, Instrotech , Pressure Measurement & Control
Temperature is a key physical variable for ensuring quality in the production of plastic film. The application of non-contact temperature measurement technology poses the challenge that films with a thickness ...

Read more...