Keeping production strictly on schedule in any facet of the food and beverage industry whether it is pumps, conveyors or electrical connections means downtime is not an option. Comtest advocates including infrared inspections (IR) into the maintenance mix. Its range of high performance, thermal imagers makes year-round spot-testing possible, specifically troubleshooting and monitoring transformers, switches, disconnects and MCCs; pumps, motors and compressors; valve operation; tank and sludge levels; level control performance; pipe blockages and integrity; operating temperature; conveyors and roller bearings; boilers and chillers; HVACR; and roof moisture, air leaks and insulation issues.
By performing quick infrared spot checks, maintenance technicians can uncover potential failures, thus allowing for timeous repairs when convenient. The line can be kept moving by frequently scanning and troubleshooting critical equipment. Traditional troubleshooting using trial and error can be effective, but also time consuming and costly. What is critically important is to pinpoint an issue quickly within a mass of sprawling production lines, because every second of downtime is expensive.
Equipment cost has historically forced plant managers to outsource annual infrared inspections, and in many cases, limit the scope of work. Annual scans certainly uncover problems, but users should not have to ‘hope for the best’ until next year’s scan. Food and beverage production demands reliability, so yearly spot checks are just not enough. The production line monitor can narrow down and rule out possible problem-causes faster by seeing the whole picture with infrared, allowing varying temperatures of components to tell the inside story.
Quick tips for performing successful IR inspections
1. Ensure consistent frequency: Extra to troubleshooting, infrared inspections of all major components and connections should be performed at least bi-annually.
2. Adjust for emissivity: Components and materials emit their energy differently. For accurate findings, ensure that the proper emissivity setting is being used for the material that is being inspected. Also, consider altering the surface by adding tape or paint to increase emissivity.
3. Perform qualitative measurements: Compare findings with similar components and connections under similar conditions to reveal thermal anomalies.
4. Ensure safety during inspection: Beyond electrical safety, be careful not to neglect the surroundings while performing infrared inspections. Focusing too heavily on the thermal imager can distract the personnel from rotating, cutting, or other dangerous equipment.
Common battery tester errors and what they mean Comtest
Electrical Power & Protection
Battery testers help quickly assess battery health, diagnose issues, and determine whether a battery needs a charge or replacement. This guide covers some of the most common battery tester errors, what they mean, and what can cause them.
Read more...Multifunction installation tester speeds up testing by 30% Comtest
Electrical Power & Protection
Comtest has launched the new Fluke 1670 Series Multifunction Installation Tester, which can cut the amount of time electricians and maintenance technicians spend producing reports by up to 50%,
Read more...Infrared solutions for glass manufacturing challenges
Temperature Measurement
In the glass industry, infrared temperature monitoring is crucial for maintaining product quality and process efficiency. Instrotech has infrared sensors and cameras which provide non-contact temperature measurements, making them ideal for these high-temperature environments.
Read more...Revolutionising fault location and maximising solar production Comtest
Electrical Power & Protection
Comtest has on offer the Fluke GFL-1500 solar ground fault locator, a frontline troubleshooting tool that helps technicians pinpoint active ground faults in solar photovoltaic systems.
Read more...Ground-breaking battery tester Comtest
Electrical Power & Protection
Midtronics offers the proven MVT handheld battery tester. This revolutionary tool, powered by MDX-AI, is set to redefine the standards of battery diagnostics and testing in the automotive industry.
Read more...New temperature transmitters with Profibus connectivity
Temperature Measurement
Siemens is enhancing its temperature measuring device portfolio with the transmitter duo, Sitrans TH420 PA and Sitrans TF420 PA. Both devices feature Profibus connectivity, advanced safety functions and expedited commissioning all in one unit.
Read more...Enhancing industrial efficiency through advanced temperature control Iritron
Temperature Measurement
Iritron has been offering modular smart thyristor drives to the local and international mining, minerals and metals market, including the latest new leading innovations in temperature control technology. These drives combined with advanced proportional-integral-derivative (PID) control will change the way large industries manage their heating processes, reducing costs and extending equipment lifespan.
Read more...Non-contact infrared thermometer
Temperature Measurement
AMETEK LAND has developed a new non-contact infrared thermometer for precise measurement and control during deposition processes in optical fibre manufacturing.
While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.
printer friendly version