Data Acquisition & Telemetry


Designed for the deep

September 2009 Data Acquisition & Telemetry

Instrotech’s pressure and temperature data collector is 100% waterproof.

The DCX-22 is an autonomous, battery powered instrument made of stainless steel designed to record water depth (pressure) and temperature over long periods. Pressure ranges are 0,8–11 bar with long term stability typically 0,5 mbar. Two versions are available:

DCX-22

The sensor, electronics and battery are housed in a sealed stainless steel tube. For data read-out, the DCX-22 must be recovered from the measurement point. The O-ring sealed end cap is then removed to access the data port. The DCX-22 works with an absolute pressure sensor. In shallow water depths where the influence of barometric pressure changes should be considered, it is recommended that a second data collector DCX-22 (Baro) is placed at the surface, to record the barometric pressure. The PC then calculates the differential pressure (the water depth) by subtracting the two measured values.

DCX-22 SG/VG

The sensor is connected by waterproof cable to a surface mounted housing with the data read-out port. This arrangement allows for easier data recovery from fixed installations. The DCX-22 SG/VG does not have to be removed from the dip pipe for data read out. The DCX-22 SG/VG is supplied with a 50 mm diameter fixing plate to enable mounting at the top of the dip pipe. The sensor can be sealed gauge SG, or vented gauge VG. The cable carries the vent tube for VG version sensors and the vent port in the housing is protected by a permeable Gore-Tex membrane.

For more information contact Pieter Deysel, Instrotech, +27 (0)11 462 1920, info@instrotech.co.za, www.instrotech.co.za



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

RS Components introduces RX23E-A
July 2020, RS Components SA , Data Acquisition & Telemetry
RS Components has introduced a new series of single-chip devices from Renesas, the RX23E-A microcontrollers (MCUs) which combine an analog front end (AFE) and an MCU core for use in equipment that delivers ...

Read more...
Robust oxygen analyser for challenging conditions
June 2020, Instrotech , Analytical Instrumentation & Environmental Monitoring
A major supplier of nitrogen generators has selected Michell’s XTP601 oxygen analyser to ensure N2 quality as part of its engineered systems for the oil and gas industry in the Middle East. The containerised ...

Read more...
Process moisture analyser
July 2020, Instrotech , Analytical Instrumentation & Environmental Monitoring
Michell Instruments has announced that an independent report confirms excellent measurement performance of its OptiPeak TDL600 process moisture analyser. A new report undertaken by DBI Gas und Umwelttechnik ...

Read more...
Advanced pump control
July 2020, Instrotech , Valves, Actuators & Pump Control
Factory automation continues to develop year on year and pumps are increasingly required to supply real-time operating data to control networks so that their performance can be monitored and adjusted ...

Read more...
Covid-19 early detection strategy
May 2020, Instrotech , Sensors & Transducers
Instrotech would like to make it known that it has a specialised early detection system on offer, that allows for fast, non-contact screening and identification of school learners, tertiary students and ...

Read more...
Electromagnetic flowmeter upgrade
May 2020, Instrotech , Flow Measurement & Control
Instrotech has announced that the Kobold magnetic inductive flowmeters MIM and MIS have been upgraded and further developed as follows: Kobold MIM, for measuring and monitoring of conductive liquids, ...

Read more...
Oval wheel flowmeters
April 2020, Instrotech , Flow Measurement & Control
Instrotech has on offer three Kobold oval wheel flowmeters that give precise flow measurement for all viscous, non-abrasive clean liquids and can be used in a number of diverse applications, such as measurement ...

Read more...
Mini oval wheel flowmeter
April 2020, Instrotech , Flow Measurement & Control
Instrotech now offers another space miracle from Kobold for OEM customers. With an all stainless steel body and temperature measurement for fuel consumption, the DOE offers different pulse output options, ...

Read more...
Inspection system for coronavirus detection
April 2020, Instrotech , Temperature Measurement
The coronavirus and other diseases are highly infectious and transferred by sick people or contaminated objects. Globally, aircraft are one way that this virus is quickly exported worldwide. China, the ...

Read more...
Kobold optimises gas burner maintenance
Technews Industry Guide: Maintenance, Reliability & Asset Optimisation 2020, Instrotech , Maintenance, Test & Measurement, Calibration
Whenever the flow of gases needs to be adjusted or monitored, Kobold’s model UTS variable area flowmeter for monitoring gas burners offers a solution. This compact measuring instrument can be placed at ...

Read more...