In pulp and paper processes, great emphasis is placed on reducing the costs of brown stock washing. The main purpose is that the black liquor and pulp must be separated after they exit the digester, so that the pulp can go onto the papermaking process. This separation occurs on brown stock washers, where water is used to wash the black liquor from the pulp. The efficiency of the brown stock washing operation has a big influence on costs, chemical recovery and environmental compliance.
Concentration of chemicals is key
Brown stock, the ‘dirty’ pulp coming out of the digester, is washed in a concurrent system with cleanliness increasing with each wash. The goal is to achieve clean stock using a minimum amount of fresh water and to avoid unnecessary dilution of the white liquor chemicals fed at the digester. These chemicals are concentrated in the recovery boiler, and a high concentration of water makes this process inefficient or even impossible.
The concentration of chemicals in the solution coming out of the last stage washer determines the cleanliness of the stock as well as the dilution factor. At this stage, fresh water is added to the system. The amount added determines the cleanliness of the stock, and the concentration of chemicals in the solution going to the recovery boiler. There is a fine balance between effective washing and conservation of the liquor concentration for downstream processing.
Even though it is called the dilution factor, concentration of the brown stock is fairly high and can be successfully determined by conductivity measurement. At this stage in the process, conductivity is in the range of 50 to 100 mS/cm, depending on the individual plant, process and stock. That corresponds to concentrations in the low one digit percent range. Dilution in that sense is relative to the two digit concentrations present in the digester. Conductivity measurement at the brown stock washers requires a sensor that is immune to clogging from pulp fibres and that can tolerate the white liquor chemicals.
Mettler Toledo’s Ingold InPro 7250 inductive conductivity sensor and M400 transmitter offers a solution for this application. The InPro 7250 is designed for in-line measurements of conductivity/concentration in pulp and paper processes. Using the InPro 7250 probe, no electrodes are directly in contact with the process and therefore not directly affected by contamination. The InPro 7250 is constructed of PEEK, which is highly resistant to the white liquor chemicals. For best performance, the InPro 7250 should be installed where it will be in contact with a representative sample of the washing solution, for example, in the washer itself or in the drain line.
The M400 transmitter offers simple operation, precise and reliable measurements and accepts both analog probes and digital sensors.
Telco sensors in conveyor belt monitoring
Sensors & Transducers
Gail Norton Instrumentation Agencies has developed a low-maintenance conveyor belt monitoring unit built on robust Telco infrared sensors, detecting belt tear and misalignment reliably in harsh coal mining environments.
Read more...Inductive ring sensors monitor material flow in feeding technology ifm - South Africa
Sensors & Transducers
ifm’s inductive ring sensors detect metallic parts such as screws and nuts as they pass through tubes at speeds up to 35 m/s, enabling precise counting, flow control and blockage detection, with sensitivity and output functions configurable via IO-Link.
Read more...Reliable 1D and 2D code reading made simple SICK Automation Southern Africa
Sensors & Transducers
SICK’s new sensingCam SEC200 image-based code reader brings supermarket-checkout simplicity to logistics and industrial identification, reading 1D and 2D codes reliably with quick browser-based setup, rugged IP65 construction and CRA-compliant cybersecurity.
Read more...Market opportunity for sensors in humanoid robots
Sensors & Transducers
A new IDTechEx report forecasts the market for sensors in humanoid robots will exceed $6,59 billion by 2037, driven by perception sensors, force/torque sensors, encoders and inertial measurement units across a growing range of commercial robot platforms.
Read more...The wireless route to safer, more efficient mining operations Emerson Automation Solutions
Editor's Choice Sensors & Transducers
Modern wireless level measurement technologies are helping mining operations improve process control, increase safety and reduce installation costs. Emerson’s Rosemount 3408 wireless non-contacting radar level transmitter uses 80 GHz frequency-modulated continuous wave radar with HART communication to reach remote assets where cabling is impractical.
Read more...Telco sensors for harsh environments
Sensors & Transducers
Telco sensors are designed to operate where moisture, particulate contamination and surface fouling would disable conventional sensors, with a range including an adjustable five-metre infrared proximity sensor for harsh industrial environments.
Read more...The data-driven path to sustainable manufacturing ifm - South Africa
Editor's Choice Sensors & Transducers
Smart automation is closing the gap between operational efficiency and environmental responsibility, and the data to do it is already inside the plant. With ifm’s sensing and digitalisation technologies, manufacturers can turn machine intelligence into measurable sustainability gains.
Read more...Expanding visibility in mining operations Emerson Automation Solutions
Editor's Choice Sensors & Transducers
Advances in wireless communications, condition monitoring and sensing technologies are helping mining operators extend measurement into previously under-monitored areas, improving equipment reliability, process performance and water stewardship.
Read more...Fiber-optic amplifiers for precise object detection ifm - South Africa
Sensors & Transducers
The OCF fibre-optic amplifier detects even the smallest or most transparent objects in confined spaces, making proven fibre-optic technology easier and more user-friendly than before.
While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.
printer friendly version