Flow Measurement & Control


Measuring volumetric flow by means of oscillation

August 2017 Flow Measurement & Control

Kobold offers the DOG range of flowmeters that use the unique oscillation principle to measure dry or humid gases even in low pressure applications.

In this measuring procedure, a partial stream of the medium is led into the measuring cell by means of a bypass. In the measuring cell, the medium flows through a chamber with two flow channels. A gate allows the stream to flow through either the left or the right channel. The flow creates over-pressure on one side and under-pressure on the other. The difference in pressure directs the media stream to the other side. This results in the stream between the two sides oscillating, which sets the medium in the connecting channel into vibration. The frequency of the oscillation is directly proportional to the flow speed. A detector determines the oscillation in the connecting channel and converts it into an electrical signal. The signal is processed further in the downstream electronic unit and then displayed or output in another form.

The devices within the DOG flowmeter family are designed for tough industrial use. They are offered in flange or intermediate flange versions up to nominal widths DN 200 in stainless steel. This means that the equipment can be used for many different applications, such as compressed air, natural gas, biogas, fermentation gas, propane, hydrogen gas and many more. Approval by the European ATEX guideline and IECEx also means that explosive gas streams can be safely measured.

The oscillation system requires only a low feed pressure and can also be used in biogas applications where measurement can otherwise be difficult. Generously dimensioned channels mean that the measuring devices are less prone to dirt deposits. There are no moving parts in the media stream and therefore there is no wear.

The advantages are: reliable performance maintained over a long lifetime; a high degree of measuring accuracy; not prone to dirt deposits; no wear and large measuring ranges.

For more information contact Instrotech, +27 (0)10 595 1831, sales@instrotech.co.za, www.instrotech.co.za



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

Optimisation of alkaline electrolysers
Samson Controls Flow Measurement & Control
his application study relates to the use of a smart meter valve in alkaline electrolysers, and is based on proven experience with one of the biggest hydrogen electrolyser producers in the world. The project proves that the smart meter valve’s added functionality creates an ideal setup in alkaline electrolysers for reducing cost and improving functionality and system performance.

Read more...
Preventing spills and improving operational efficiency
Flow Measurement & Control
In an industry where every spill carries a hefty price tag, Point Energy Partners found that the manual and low-tech systems at their saltwater disposal sites were a significant problem.

Read more...
Wind turbines with smart sensors
Instrotech Motion Control & Drives
The wind’s usable kinetic energy increases with the wind speed. Wind turbines, therefore, use kinetic energy to generate torque and then rotational movement. The rotor, consisting of three rotor blades, ...

Read more...
Infrared camera for condition monitoring and early fire detection
Instrotech Temperature Measurement
The Optris PI 640i thermal imager is the smallest measuring VGA infrared camera, with a body-sized volume of 45 x 56 x 90 mm, and weighing only 269 to 340 g, depending on the lens. It counts among the most compact thermal imaging cameras on the market.

Read more...
Ultracompact mass flow meters with advanced transmitters
Emerson Automation Solutions Flow Measurement & Control
Emerson has introduced the Micro Motion G-Series line of Coriolis mass flow and density meters, the most compact dual-tube Coriolis mass flow meters on the market. They offer the same level of quality and reliability as standard designs, but in a much smaller and lighter form factor.

Read more...
Accurate flowmeter for oil & gas
Endress+Hauser South Africa Flow Measurement & Control
Promass Q, the high-tech Coriolis flowmeter from Endress+Hauser, is now also available for larger pipe sizes with maximum flow rates between 850 and 2400 tph.

Read more...
Pressure monitoring for oil and water tempering machines
Instrotech Pressure Measurement & Control
Temperature plays a significant role in many manufacturing processes. In such cases, a tempering machine is used to maintain the manufacturing process at the desired temperature. Keller supplied PR-21Y piezoresistive pressure transmitters to a client specialising in developing and producing oil and water tempering machines.

Read more...
Optimising CIP processes with precision instrumentation
Endress+Hauser South Africa Flow Measurement & Control
Many food and beverage manufacturers encounter challenges with CIP processes that take too long. Have you considered exploring potential solutions to address these issues?

Read more...
How predictive maintenance will help tackle water scarcity
ABB South Africa Flow Measurement & Control
The water industry is facing increasing pressure to optimise treatment processes and address the impending global water crisis. ABB’s global product line manager, Krishna Prashanth suggests how the integration of smart instrumentation and predictive maintenance can ensure the highest quality treatment of water.

Read more...
Flowmeters with faster and more reliable data transmission
ABB South Africa Flow Measurement & Control
ABB has launched the CoriolisMaster and ProcessMaster flowmeters, which can be powered over the same Ethernet cable used for data transmission, eliminating the need for separate cabling.

Read more...